The Linux Channel

a Linux and Tech Youtube Channel for advance Linux users, systems and network software programmers and tech enthusiasts

Arduino UNO

Using a GPS Sensor #IoT #GPS #ArduinoUNO #Skylab-SKG13BL

By thelinuxchannel #Arduino, #Arduino UNO, #Arduino UNO project, #Circuits, #courses, #Electronics, #embedded systems, #Github, #GPS, #GPS Receiver, #GPS Sensor, #IoT, #kernel programming, #NMEA protocol, #programming, #Skylab SKG13BL, #student, #TinyGPS
Skylab SKG13BL GPS Receiver with Arduino UNO - The Linux Channel
Skylab SKG13BL GPS Receiver with Arduino UNO - The Linux Channel

This article is submitted by: Saumitra Kapoor
If you want to publish your articles, you can kindly contact me via email and send your article submissions (content and the resources). Once reviewed, I should accept and post the same 🤗

My name is Saumitra Kapoor and I am in love with Electronics, Circuits, Wires and Devices. I started learning everything about it long back from wherever I could and I haven’t stopped since. I try to read a lot, build fun projects and come up with tutorials.

A GPS receiver uses satellites to pinpoint locations, so as long as you have a GPS receiver and a clear view of the sky, you’ll never be lost again. So here is a sample Arduino UNO project where you can interface a GPS Receiver such as Skylab SKG13BL.

Have a look at this amazing site to know more about a GPS Sensor: http://electronics.howstuffworks.com :: How GPS Receivers Work

I would suggest have a look at how the GPS receiver generates a Pseudo Random Code which has a mention in the given site. The GPS system uses an array of satellites orbiting around the earth and sending time information. It picks up the signal transmitted from the satellites, calculates the time it took for the signal to arrive, and by identifying the position of satellites, triangulates the position on the surface of the globe. It uses the standard NMEA protocol (http://www.nmea.org) to transmit the position data via serial port. Let us start exploring the world of GPS!

GPS Satellites

Here is a list of components needed:

Here is an image of this module:

GPS Receiver - Skylab SKG13BL
GPS Receiver - Skylab SKG13BL module1
GPS Receiver - Skylab SKG13BL module2

The connections are as follows:

Skylab SKG13BL GPS Receiver with Arduino UNO

GND of GPS ———— GND of Arduino
3.3V of GPS ————- 3.3V on Arduino

Note: Skylab SKG13BL: It is always a good practice to read the Datasheet. So here you go: http://www.alselectro.com/files/SkyLab_Datasheet.pdf
Note : You can even use a 12V Power source, but here we are using 3.3V.

Most microcontrollers these days have built in UARTs (universally asynchronous receiver/transmitter) that can be used to receive and transmit data serially. UARTs transmit one bit at a time at a specified data rate (i.e. 9600bps, 115200bps, etc.). This method of serial communication is sometimes referred to as TTL serial (transistor-transistor logic).

The last simple connection involves connecting the TLL from GPS to Arduino Board:
Rx of GPS ——– Tx of Arduino (Pin 3)
Tx of GPS ——— Rx of Arduino (Pin 4)

* Refer Pg.8 of the Datasheet.

Now, connect the G Mouse to the GPS Receiver and connect the Arduino board to the PC via USB.

Libraries/Dependencies:
Here are the required libraries we need to install.
Install the TinyGPS Library from here: http://arduiniana.org/libraries/tinygps/
Install the Software Serial Library: https://www.arduino.cc/en/Reference/SoftwareSerial

Please take care of the following:

  • Do not connect the GPS Module to Multiple Power Supplies.
  • Place the G Mouse at a spot where it can see the sky.
  • Please go through the Datasheet.
  • You can even use Putty to obtain output (in Windows) – http://www.putty.org/
  • If the code shows error, make sure to keep the Baud Rate to 9600.
  • If you face port or driver problem,
    Do this (in Windows): Control Panel > System and Security > System > Device Manager > Ports > Arduino UNO > Update Driver Software > Browse computer manually and choose the Arduino IDE folder.

Source code:
Download the code HERE.
Kindly remember to refer the previous step in case of Port Error.

Output:
The code will give the Latitude and Longitude. Make sure to divide the output by 10^6 to get correct coordinates.

You can also visit sites likes to map the points:

So here is the output it generates:

Position: lat: 26865785 lon: 80906375 Position: lat: 26865785 lon: 80906375 Position: lat: 26865785 lon: 80906375 Position: lat: 26865783 lon: 80906375 Position: lat: 26865783 lon: 80906375 Position: lat: 26865783 lon: 80906375 Position: lat: 26865783 lon: 80906375 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906373 Position: lat: 26865783 lon: 80906372 Position: lat: 26865783 lon: 80906372 Position: lat: 26865783 lon: 80906370 Position: lat: 26865783 lon: 80906370 Position: lat: 26865783 lon: 80906370 Position: lat: 26865783 lon: 80906370 Position: lat: 26865783 lon: 80906372 Position: lat: 26865783 lon: 80906372 Position: lat: 26865783 lon: 80906375

Post Views: 407

By thelinuxchannel

Related Post

Arduino UNO

Slow RGB LED Fade via Arduino UNO

thelinuxchannel